Customers Also Viewed.Liftmaster csw24ul manual
Looking for:
Liftmaster csw24ul manual |
Liftmaster csw24ul manual.YOU CAN STILL ADD MORE!
Table Of Contents. Quick Links. See also: Troubleshooting Manual , Reference Manual. Table of Contents. Previous Page. Next Page. The gate the line-of-sight of the gate. Activation of the reset control shall not operator is only one component. For a copy, contact ASTM directly at or www. Before trenching, contact underground standards refer to page 4. Gate must fit specifications of operator utility locating companies.
Gate Hinge Center 4" Position the operator arm onto the output shaft so that the pin slides into the slot. Weld the gate bracket to the gate. Weld the short arm section. Weld the long arm section. Remove the set screws from the arm. NOTE: Completely weld around the outer tubing and bracket. Refer to the specific entrapment protection device manual for more information. These entrapment protection device inputs are for monitored devices, which include pulsed photoelectric sensors, resistive edge sensors, and pulsed edge sensors.
The ground wire must be a single, whole piece of wire. Never splice two wires for the ground wire. If you should cut the ground wire too short, break it, or destroy its integrity, replace it with a single wire length. Remove the outlet housing from the electrical box by removing the screws 2. Pull the outlet housing out and locate the power wiring connector on the EMI board. The batteries are for battery backup or solar installation.
The 33AH application requires the 33AH wire harness Model K and an additional battery tray Model K to allow more space in the enclosure. The heater option cannot be used with the 33AH battery application.
Follow the directions according to your application. Do not use wired and wireless communication simultaneously. Wired dual gate applications will have a longer battery standby time than wireless applications.
Use PVC conduit to prevent damage to cables. Disconnect ALL power to the operator and unplug the J15 plug from the control board. The front cover can easily be removed to access the electrical box. To access the reset switch slide the access door up.
The front cover and access door can be locked with the key. Based on the length and weight of the gate it may be necessary to make additional force adjustments. When programming a third keyless entry to the operator, the first keyless entry will be erased to allow the third keyless entry to be programmed. To program the operator to the LiftMaster Internet Gateway: 2. Your specific site requirements may be different. Always setup the operator system to the site requirements, including all necessary entrapment protection devices.
The firmware version will show after the operator type, example "1. Release the handle on the operator arm to allow the gate to be opened and closed manually. On a dual gate application the handle must be released on both operators. To resume normal function tighten the handle by pushing it down.
Used for exit probe, telephone entry, external exit loop detector, or any device that would Shadow command the gate to open. Relay activates prior to motor activation and during motor run. Relay is off when motor is off.
Function of relay contact activation determined by switch settings. Some codes are saved in the code history and some are not. If a code is not saved it will briefly appear on the display as it occurs, then disappear. Adjust settings as needed. Check that correctly. Solenoid has power do not power solenoid from control board accessory power terminals. If the operator arm will hit an obstruction when the gate is in the open position follow the directions for Compact Installation.
If the distance is greater than 4" Take the operator arm apart and remove the inner sleeves from the long arm section outer tubing. In general, the panel s should be mounted using the provided angle bracket facing due south. Use a compass to determine direction. The solar panel s should be mounted in an area clear of all obstructions and shading from buildings and trees.
Position solar bracket on mounting surface. Mark and drill holes. Insert two bolts into the track located on the back of the solar panel s. Mounting Surface 3. Slide bolts in track away from bolt hole and align both bolts. Single-button to 4-button, visor or key chain. Posts not included. Print page 1 Print document 60 pages. Rename the bookmark.
Delete bookmark? Cancel Delete. Delete from my manuals? Sign In OR. Don't have an account? Sign up! Restore password. Upload manual. Upload from disk.
Upload from URL.
Comments
Post a Comment